Non Linear Progressive Collapse Analysis of RC Frame Structure

Article Sidebar

PDF
Published: Jun 22, 2016

Main Article Content

A. U. Qazi
A. Hameed
M. Ilyas
A. Majid

Abstract

The casualties due to collapse of buildings are enormous either through blast or vehicle strike which could have been reduced if the buildings have resisted progressive collapse after the accidental removal of vital load bearing elements. In this research, progressive collapse (PC) potential of an existing reinforced concrete (RC) building has been evaluated analytically using Nonlinear FEM software following General Services Administration guidelines. Linear static, non-linear static, linear dynamic and non-linear dynamic analyses have been carried out to explore PC potential. Building under consideration was designed for Earthquake Zone-2B and has potential for PC in linear static analysis while non-linear static and non-linear dynamic analysis results have shown that there is no potential for PC. Results of analysis have been compared by taking deflection under joint where the column is removed and is used as base for comparison. Results show that linear static procedure is conservative as compared to non-linear analysis. Non-linear static and non-linear dynamic analysis provides almost similar results. There is negligible effect of material strength and damping variations on PC. In linear static analysis decrease in deflection of joint at column removal location is approximately 7% for every 7MPa (1000psi) increase in fc’ while 9% reduction is observed in nonlinear dynamic analysis. Damping that can be achieved through installation of dampers has been found beneficial up to 10% value. Increase in damping ratio beyond 10% of critical damping has negligible effect on deflection and PC.

Article Details

Issue
2015: Volume 16 JAN 2015
Section
Civil Engineering,Structures, Construction, Geo technology, Water, Transportation

References

Shariati, M., Ramli-Sulong, N. H., Arabnejad, M. M., Shafigh, P. and Sinaei, H., 2011, “Assessing the strength of reinforced concrete structures through Ultrasonic Pulse Velocity and Schmidt Rebound Hammer tests,” Scientific Research and Essay, Vol. 6, no. 1, pp. 213-220

Mirmiran, A., 2001, “Integration of NonDestructive Testing In Concrete Education”, Journal of Engineering Education, V. 90, No. 2, pp. 219-222.

Hertlein, B.H., 1992, “Role of Nondestructive Testing in Assessing the Infrastructure Crisis,” Proceedings, Materials Engineering Congress on Performance and Prevention of Deficiencies and Failures, ASCE, pp. 80–91.

Bray, D.E., 1993, “The Role of NDE in Engineering Education,” Materials Evaluation, vol. 51, no. 6, pp. 651–652.

Huang, Q., Gardoni, P. and Hurlebaus, S., 2011, “Predicting Concrete Compressive Strength Using Ultrasonic Pulse Velocity and Rebound Number”, ACI Material Journal, V. 108, No. 4, pp. 403-412

Samarin, A., and Meynink, P., 1981, “Use of Combined Ultrasonic and Rebound Hammer Method for Determining Strength of Concrete Structural Members,” Concrete International, V. 3, No. 3, pp. 25-29.

Miretti, R., Carrasco, M. F., Grether, R. O. and Passerino, C. R., 2004, “Combined NonDestructive Methods Applied to Normal-Weight and Lightweight Concrete,” Insight, V. 46, No. 12, pp. 748-753.

Hola, J., and Schabowicz, K., 2005, “New Technique of Nondestructive Assessment of Concrete Strength Using Artificial Intelligence,” NDT&E International, V. 38, pp. 251-259.

Wiebenga, J. G., 1968, “A Comparison between Various Combined Non-Destructive Testing Methods to Derive the Compressive Strength of Concrete,” Report kB1-68-61/1418, Inst. TNO Veor Bouwmaterialen en Bouwconstructies, Delft, the Netherlands

Kheder, G. F., 1999, “A Two Stage Procedure for Assessment of In-Situ Concrete Strength Using Combined Non-Destructive Testing,” Materials and Structures, V. 32, No. 6, pp. 410- 417.

Arioglu, E., Odbay, O., Alper, H. and Arioglu, B., 1994, “A New Formula and Application Results for Prediction of Concrete Compressive Strength by Combined Non-Destructive Method,” Concrete Prefabrication, Association of Prefabrication Manufacturers, V. 28, pp. 5- 11. (in Turkish)

Basu, A. and Aydin, A., 2004, “A method for normalization of Schmidt hammer rebound values,” Int. J. Rock Mech. Mining Sci., Vol. 41, no. 7, pp. 1211-1214

ASTM C805-02, “Standard Test Method for Rebound Number of Hardened Concrete,” ASTM International, West Conshohocken, PA., USA

Mirmiran, A. and Wei, Y., 2001, “Damage Assessment of FRP-Encased Concrete using Ultrasonic Pulse Velocity,” Journal of Engineering Mechanics, Vol. 127, No. 2, pp. 126–135

Popovics, S., Rose, J. L., and Popovics, J. S., 1990, ‘‘Behavior of ultrasonic pulses in concrete.’’ Cement and Concrete Res., V. 20, no. 2, pp. 259–270.

Popovics, J. S., and Rose, J. L., 1994, ‘‘Survey of developments in ultrasonic NDE of concrete.’’ IEEE Trans. on Ultrasonics, Ferroelectrics, and Frequency Control, V. 41, no. 1, pp. 140–143.

Selleck, S., Landis, E. N., Peterson, M. L., and Shah, S. P., 1996, ‘‘NDE of distributed cracking in concrete.’’ Proc., 11th Conf. Engrg. Mech., ASCE, New York, pp. 604–607.

Turgut, P., 2004, “Research into the correlation between concrete strength and UPV values,” NDT. net, V. 12, no. 12.

Sturrup, V., Vecchio, F. and Caratin, H., 1984, “Pulse velocity as a measure of concrete compressive strength,” Situ/Nondestructive Testing of Concrete, ACI SP-82, pp. 201-227

Yaman, I. O., Inei, G., Yesiller, N. and Aktan, H. M., 2001, “Ultrasonic Pulse Velocity in Concrete Using Direct and Indirect Transmission,” ACI Materials Journal, V. 98, No. 6, pp. 450-457

BS EN 12504-4: 2004, “Testing Concrete. Determination of Ultrasonic Pulse Velocity,” British Standard Institute, London, U.K.

ASTM "C 597, 2002, “Standard test method for pulse velocity through concrete,” ASTM International, West Conshohocken, PA., USA

ILEM/NDT 1 1971, “Testing of Concrete by the Ultrasonic Pulse Method,” RILEM, Bagneux, France.

ACI Committee 214, 2011, “Guide to Evaluation of Strength Test Results of Concrete (ACI 214R-11),” American Concrete Institute, Farmington Hills, MI.

IS 13311 (Part 1) 1992, Non-Destructive Testing Of Concrete, Part 1 Ultrasonic Pulse Velocity, Bureau of Indian Standards, Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi

Trtnik, G.; Kavcic, F.; and Turk, G., 2009, “Prediction of Concrete Strength Using Ultrasonic Pulse Velocity and Artificial Neural Networks,” Ultrasonics, V. 49, pp. 53-60.